You have no items in your shopping cart.
Item Specifics
CONDITION: New: A brand-new, unused, unopened and undamaged item in original retail packaging (where packaging is applicable). If the item comes direct from a manufacturer, it may be delivered in non-retail packaging, such as a plain or unprinted box or plastic bag. See the seller's listing for full details. See all condition definitions
EAN: Does Not Apply
BRAND: Unbranded/Generic
MPN: Does Not Apply
PRODUCT DETAILS:
MQ-2 gas sensor sensitive material used in the clean air low conductivity tin oxide (SnO2). When there is the environment in which the combustible gas sensor, conductivity sensor with increasing concentration of combustible gases in air increases. Using a simple circuit to convert the change in conductivity of the gas concentration corresponding to the output signal. MQ-2 gas sensor high on gas, propane, hydrogen sensitivity of detection of natural gas and other flammable vapours are also very good. This sensor can detect a variety of flammable gas, is a low-cost sensor for a variety of applications.
Module description:
Using high-quality dual-panel design, with power indicator and TTL signal output instructions ;
The switching signal having a DO (TTL) output and analog output AO;
TTL output valid signal is low. (Low-level signal when the output light can be directly connected to the microcontroller or relay module)
Analog output voltage with the higher concentration of higher voltage.
A gas, natural gas, city gas, smoke better sensitivity.
There are four screw holes for easy positioning;
Has a long life and reliable stability
Rapid response and recovery characteristics
Specifications:
- Product dimensions: 32 x 20 x 15 (L x W x H)
- Chip: LM393, ZYMQ-2 gas sensors
- Working voltage: DC 5V
- Detection of gas: combustible gases, fumes
- Detectable concentration: 300-10000ppm (flammable gas)
Electrical properties:
Input voltage: DC5V
Power consumption (current): 150mA
DO output: TTL digital 0 and 1 (0.1 and 5V)
AO output: 0.1 - 0.3V (relative to pollution), the maximum concentration of a voltage of about 4V
Special note: After the sensor is powered, needs to warm up around 20S, measured data was stable , heat sensor is a normal phenomenon , because the internal heating wire , if hot is not normal.
Wiring:
- VCC: positive power supply (5V)
- GND: power supply is negative
- DO: TTL switching signal output
- AO: analog signal output
Module Applications:
Gas may be used in homes and factories leakage monitoring device suitable for the detection of gas, butane, propane, methane , smoke , etc.
Package includes:
1 x MQ-2 module
Item Specifics
CONDITION: New: A brand-new, unused, unopened and undamaged item in original retail packaging (where packaging is applicable). If the item comes direct from a manufacturer, it may be delivered in non-retail packaging, such as a plain or unprinted box or plastic bag. See the seller's listing for full details. See all condition definitions
EAN: Does Not Apply
BRAND: Unbranded/Generic
MPN: Does Not Apply
PRODUCT DETAILS:
MQ-2 gas sensor sensitive material used in the clean air low conductivity tin oxide (SnO2). When there is the environment in which the combustible gas sensor, conductivity sensor with increasing concentration of combustible gases in air increases. Using a simple circuit to convert the change in conductivity of the gas concentration corresponding to the output signal. MQ-2 gas sensor high on gas, propane, hydrogen sensitivity of detection of natural gas and other flammable vapours are also very good. This sensor can detect a variety of flammable gas, is a low-cost sensor for a variety of applications.
Module description:
Using high-quality dual-panel design, with power indicator and TTL signal output instructions ;
The switching signal having a DO (TTL) output and analog output AO;
TTL output valid signal is low. (Low-level signal when the output light can be directly connected to the microcontroller or relay module)
Analog output voltage with the higher concentration of higher voltage.
A gas, natural gas, city gas, smoke better sensitivity.
There are four screw holes for easy positioning;
Has a long life and reliable stability
Rapid response and recovery characteristics
Specifications:
- Product dimensions: 32 x 20 x 15 (L x W x H)
- Chip: LM393, ZYMQ-2 gas sensors
- Working voltage: DC 5V
- Detection of gas: combustible gases, fumes
- Detectable concentration: 300-10000ppm (flammable gas)
Electrical properties:
Input voltage: DC5V
Power consumption (current): 150mA
DO output: TTL digital 0 and 1 (0.1 and 5V)
AO output: 0.1 - 0.3V (relative to pollution), the maximum concentration of a voltage of about 4V
Special note: After the sensor is powered, needs to warm up around 20S, measured data was stable , heat sensor is a normal phenomenon , because the internal heating wire , if hot is not normal.
Wiring:
- VCC: positive power supply (5V)
- GND: power supply is negative
- DO: TTL switching signal output
- AO: analog signal output
Module Applications:
Gas may be used in homes and factories leakage monitoring device suitable for the detection of gas, butane, propane, methane , smoke , etc.
Package includes:
1 x MQ-2 module
size | chest(in.) | waist(in.) | hips(in.) |
---|---|---|---|
XS | 34-36 | 27-29 | 34.5-36.5 |
S | 36-38 | 29-31 | 36.5-38.5 |
M | 38-40 | 31-33 | 38.5-40.5 |
L | 40-42 | 33-36 | 40.5-43.5 |
XL | 42-45 | 36-40 | 43.5-47.5 |
XXL | 45-48 | 40-44 | 47.5-51.5 |
size | chest(in.) | waist(in.) | hips(in.) |
---|---|---|---|
XS | 34-36 | 27-29 | 34.5-36.5 |
S | 36-38 | 29-31 | 36.5-38.5 |
M | 38-40 | 31-33 | 38.5-40.5 |
L | 40-42 | 33-36 | 40.5-43.5 |
XL | 42-45 | 36-40 | 43.5-47.5 |
XXL | 45-48 | 40-44 | 47.5-51.5 |